Sales (860) 741-3761
|
Loading...
|
Service (860) 253-3363
Loading...
|
Parts (860) 253-3362
Loading...
(860) 741-3761 Loading...
Sales
Service

Ownership Guide

How to Reset the Toyota Tire Pressure Light

What the light means, how to set the pressure, the two ways Toyota resets the system, and when a blinking light means a trip to the shop.

In most cases you do not need to reset anything. Set all four tires to the pressure on the driver’s door jamb label and the light usually goes out by itself within a few minutes. A reset, which Toyota calls initialization, is needed after the tires are rotated or the pressure is changed. If the light blinks for about a minute and then stays on, the system itself has a fault and adding air will not clear it.

Last reviewed: November 2026. Steps come from Toyota owner’s manuals, including the 2024 Highlander Hybrid. Menus and button locations vary by model and year, so check the “Tire pressure warning system” pages of your owner’s manual.

Solid or Blinking: What the Light Is Telling You

What you see What it means What to do
Light comes on and stays on One or more tires are low Stop somewhere safe, check for a puncture, and set the pressure
Light blinks for about a minute, then stays on A fault in the tire pressure warning system Have it checked. The system may not be able to warn you of a low tire
Light blinks 3 times during a reset The reset has started Normal. Drive to finish it

Not sure which you have? Toyota’s manual suggests switching the vehicle off and on again and watching the light as it starts up.

First, Set the Tire Pressure

  1. Check the tires when they are cold, before driving or after the car has sat for a few hours.
  2. Find the recommended pressure on the tire and loading information label on the driver’s door jamb. Do not use the maximum pressure printed on the tire sidewall.
  3. Check all four tires with a gauge and add air to match the label.
  4. Drive normally. Toyota says the light usually turns off a few minutes after the pressure is corrected.

If the light is still on several minutes later and the pressures are right, do the reset below.

How to Reset From the Display (Newer Toyotas)

Newer Toyotas reset the system through the screen in the instrument cluster, using the arrow and OK buttons on the steering wheel. These steps are from the 2024 Highlander Hybrid manual, and the RAV4 manual we checked uses the same menu.

  1. Park and switch the vehicle off. The reset cannot be done while moving.
  2. Set all four tires to the cold pressure on the door jamb label.
  3. Switch the vehicle to ON.
  4. On the instrument cluster display, open the settings menu.
  5. Select Vehicle Settings, then press and hold OK.
  6. Select TPWS.
  7. Select Set Pressure, then press and hold OK until the tire pressure light blinks 3 times.
  8. Drive at about 25 mph or more. The reset finishes after roughly 10 to 30 minutes of driving.

If it has not finished after an hour, Toyota says to park for about 20 minutes and drive again.

How to Reset With the Reset Button (Older Toyotas)

Older Toyotas have a tire pressure warning reset switch. It is usually low on the dashboard under the steering column, and your owner’s manual shows the exact spot.

  1. Park and switch the vehicle off.
  2. Set all four tires to the cold pressure on the door jamb label.
  3. Turn the ignition to ON without starting the engine.
  4. Press and hold the reset switch until the tire pressure light blinks slowly 3 times.
  5. Drive at about 25 mph or more for about 10 minutes.

When a Reset Is Needed, and When It Is Not

Toyota’s manual calls for a reset after the tires are rotated, after the tire pressure is changed on purpose, and after new sensor ID codes are registered. It is not a way to turn off a light caused by a low tire.

This matters because the reset tells the system that the current pressure is correct. If you reset with a low tire, the system uses that low pressure as its reference and may not warn you later. Always set the pressure first.

Why the Light Comes On in Cold Weather

Air pressure drops as temperature falls, by roughly 1 psi for every 10°F. A tire that was set correctly on a warm September afternoon can read several psi low on the first cold morning in November. On top of normal air loss, that is often enough to turn the light on. Toyota’s manual lists natural air loss and temperature changes as normal causes.

The fix is the same: add air to the door jamb pressure while the tires are cold. The light may go out after the tires warm up on the road, but the pressure is still low, so top them off anyway.

Winter Tires on a Second Set of Wheels

Each wheel has a pressure sensor with its own ID code, and the car only listens to the codes it has on file. If your winter tires are mounted on their own wheels with their own sensors, those codes have to be registered when the wheels go on. Until they are, the light will blink and then stay on.

Newer Toyotas can register a second set through the Change Wheel option in the same TPWS menu, followed by a reset. On older models a dealer registers the codes.

When to Stop Driving

If the light comes on while you are driving, Toyota’s manual says to stop in a safe place as soon as you can and check the tires. Avoid hard steering and braking on the way. If the light stays on after you have added air, the manual says a tire is probably flat or losing air.

Tire Light Check

We can check all four tires, find a slow leak, test the sensors and register winter wheels.

Common Questions

Toyota Tire Pressure Light FAQ

How do I reset the tire pressure light on a Toyota?

Set all four tires to the pressure on the driver’s door jamb label first. On newer Toyotas, open the settings menu on the instrument cluster display, choose Vehicle Settings, then TPWS, then Set Pressure, and hold OK until the light blinks 3 times. On older Toyotas, turn the ignition on and hold the reset switch until the light blinks slowly 3 times.

Where is the tire pressure reset button on a Toyota?

On older Toyotas that have one, the tire pressure warning reset switch is usually low on the dashboard under the steering column. Newer Toyotas do not have a button and use the TPWS menu on the instrument cluster display. Your owner’s manual shows the location for your model.

Why is my Toyota tire pressure light on when the tires look fine?

A tire can be several psi low without looking flat, so check all four with a gauge. Cold weather is a common cause, since pressure falls about 1 psi for every 10°F. If the pressures are correct and the light blinks at start-up before staying on, the system has a fault and should be checked.

What does a blinking tire pressure light mean on a Toyota?

If the light blinks for about a minute and then stays on, Toyota’s manual says there is a malfunction in the tire pressure warning system. The system may not be able to detect a low tire until it is repaired.

Do I need to reset the tire pressure system after a tire rotation?

Yes. Toyota’s owner’s manual lists tire rotation as one of the times the system has to be initialized, along with changing the tire pressure and registering new sensor ID codes.

How long do I have to drive after resetting the tire pressure light?

On newer Toyotas, drive at about 25 mph or more for roughly 10 to 30 minutes. On older models with a reset switch, Toyota’s manual gives about 10 minutes. Stops at traffic lights can make it take longer.

Why does my tire pressure light come on in cold weather?

Tire pressure falls as the air gets colder, by roughly 1 psi for every 10°F. Combined with normal air loss over a few months, a drop of 30 or 40 degrees between seasons is often enough to turn the light on. Add air to the door jamb pressure while the tires are cold.

Light Still On?

If the light stays on after the tires are set and the system is reset, or it blinks when you start the car, our service center in Enfield, CT can check the tires and the sensors.